Maplin Electronics is one of the UK's leading Electronics retailers, offering the most competitive choice of mainly branded, quality products at consistently the lowest prices in the local market. The core range of Maplin products include TV, video, audio, Cooking, MDA, Small domestic appliances, Communications, Multimedia, Electronics and New technology accessories. Maplin Stores are unrelated to the Dixons Stores Group - which includes Dixons, Currys, PC World and The Link.

CAT5E 90 KEYSTONE JACK WHT UK, at Maplin
• Colour: White• Warranty: Lifetime• Weight: 0.009 KG• Meets industry standard TIA/EIA 568-A-5 requirements• Balances signal transmission of insertion loss and crosstalk from 1 to 100 MHz• Panel-type unshielded RJ45 (8P8C) keystone jack• 110/KRONE IDC vertical punchdown termination for 22-26 AWG UTP solid wire• Compatible with T568A and T568B wiring with Category 5 enhanced requirement• Complies with FCC Part 68Designed for superior performance, this keystone jack will work with C2G wall plates and surface boxes or any standard keystone and angled multimedia wall plate or patch panel. Available in 9 colours to match housing or allow colour-coded port designation in compliance with TIA-606 requirements. Each keystone jack includes 110-type IDC straight-back termination with strain relief caps, and comes standard with 50 µinch gold plating on the jack contacts.

Replacement lamp for BENQ-MX812ST, at Maplin
•Complete projector lamp for the BENQ-MX812ST• Compatible with project manufacturer part code(S)-5J.J3J05.001• High Quality, High Brightness• Long Life If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Maplin Swivel HDMI Cable 0.75m, at Maplin
• Ideal for use with HDTV, Freeview, Freesat/Sky HD, PS3, PS4, Xbox One, Blu-Ray and any other HDMI device• Suitable for resolutions up to and including 1080p and 4K• Version 2.0 compatible and works with all previous specifications• 3D TV compatible• Gold-plated connectors• Durable and highly flexible outer jacket• 5 Year WarrantyHDMI is a highly versatile cable that combines high definition video and multi-channel audio into one cable. They are commonly used for connecting TVs to set satellite/cable boxes, Blu-ray/DVD players and games consoles. It’s also used in PC connectivity and mobile devices.The Maplin Range – Premium construction and specification, with marketing leading cable technologies.The Maplin Cable range delivers the latest technology first and foremost, ensuring compatibility with the latest hardware standards.Our Maplin cables feature fully wired connectors and shielded cables where required throughout the range, delivering high fidelity audio and video signals across a vast range of connectors and dedicated adapters.The Maplin cable range features hard wearing cable construction, with colour-coded, compact connectors available for almost any use. All Maplin cables are quality assured, with a 5 year warranty across the range.

Replacement lamp for INFOCUS-IN2126, at Maplin
•Complete projector lamp for the INFOCUS-IN2126• Compatible with project manufacturer part code(S)-SP-LAMP-070• Expected lamp life of 2500 Hours• 230W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

4020 CMOS Logic HCF/HEF, at Maplin
•Industry standard CMOS 4000 series device•Ripple-Carry Binary Counter•Supports power supply voltages of up to 15V and rail output swings•Ideal for hobby, industry and automotive applications•Used in a wide variety of circuit applications

Bubble Fluid with Reduced Wetting 5L, at Maplin
•A water based bubble fluid•Designed to work with most common brands of bubble machines•Produces iridescent, long lasting bubbles •High performance with very little spatter and therefore very little wastage•Only the purest de-mineralised, R/O and sterilised water is usedThis Bubble Fluid is manufactured with the highest quality chemicals and purest, sterile, water. Having spent many years in development, the Bubble Fluid is designed to give superb results in virtually all the bubble blowing machines on the market. It has an anti-bacterial formulation, greatly increasing shelf-life.The fluid produces long, continuous streams of bubbles with beautiful colours and sparkle. The bubbles are stable (therefore long lasting) and are formulated to reduce wetting on floors, greatly reducing the potential of slip hazards. Our fluid produces very little spatter, i.e. the bubbles do not splatter guests with product when they burst, which also helps to reduce potential slip hazards. As there is very little spatter you don’t waste any fluid either! The reduced wetting formula makes it great for entertainment use.

Flush Mounting F Type Outlet, at Maplin
with a standard F socket. Ideal for modern TV installations, especially digital TV including terrestrial, cable and satellite. Overall size 85mm square which fits all standard back-boxes (pattresses). Screws supplied.

PQI i-Cable Flat with Lightning Connector Green, at Maplin
•USB Charging and Sync•Apple Lightning Connector•Charge and Sync your iPhone, iPod or iPad•Keychain style with a snap lock design. which is convenient to carry and store easilyCompatible with Apple mobile devicesApple's next-generation syncing and charging cable is suitable for any of Apple's latest devices: iPhone 5s, iPhone 5c, iPod touch 5th Generation, iPod nano 7th Generation, iPad 4th Generation and iPad mini.Designed for convenient storageIn addition to the buckle specially designed for storage, the cable has been made broader to avoid tangling, making storage easier.Vivid and colorfulPQI i-Cable Flat 20 comes in five vivid colors: mysterious purple, peachy pink, sky blue, grass green, and tangy orange.

Car/air DC adapter, at Maplin
Car/air DC adapter, Allows a portable device to plug into the DC supply in a car or plane•DC, Low voltage DC input•EAN: 5055190117835•Equivalent Part Number: KC529•Voltage: 18.0VCar-Air DC Adapter 18-20V

RC U5 GYRO Helicopter Replacement Upper Rotor, at Maplin
•N01JW Upper rotor

Samsung GC-100 Galaxy Black Camera Kit inc Case Battery & Charger, at Maplins
16.3MP Seamless Connectivity (3G & Wi-Fi) 21x Super Long Zoom Android 4.1 Jelly Bean 4.8 (121.2mm) HD Super Clear Touch Display Voice Control Slow Motion Video Share Shot Auto Upload Smart Mode Get ready because photography will never be the same again. The Samsung Galaxy Camera gives you the magic of professional digital photography with the powerful intelligence of the Android 4.1 Jelly Bean OS. Its the smartest camera ever with stunning photographic output and a range of exceptionally rich professional shooting modes editing features and various apps. Going pro has never been this easy or this fun.

4046 CMOS Logic HCF/HEF, at Maplins
•Industry standard CMOS 4000 series device•MicroPower Phase Locked Loop•Supports power supply voltages of up to 15V and rail output swings•Ideal for hobby, industry and automotive applications•Used in a wide variety of circuit applications

Replacement lamp for MITSUBISHI-HD1000, at Maplin
•Complete projector lamp for the MITSUBISHI-HD1000• Compatible with project manufacturer part code(S)-VLT-HC910LP• Expected lamp life of 2000 Hours• 200W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Replacement lamp for MITSUBISHI-XD200, at Maplins
•Complete projector lamp for the MITSUBISHI-XD200• Compatible with project manufacturer part code(S)-VLT-XD200LP• Expected lamp life of 1500 Hours• 210W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Flexible Warm White Strip Lighting Extension Kit (Used), at Maplin
•Extension pack for the A42LA flexible white LED kit•Contains 3 x 50 cm flexible warm white strips and 3 x connecting pins•Warm white illumination, ideal for kitchen cabinets, bookcases, desk and cupboards

Matabi Evolution 20 Super Sprayer - 20 Litre, at Maplin
The Matabi Evolution 20 Super Sprayer has a knapsack design that is ideal for outdoor work such as garden, vegetable plots and crops. It is robust, easy to use and easy to maintain and features a large filling mouth, translucent level indicator, adjustable nozzle and adjustable padded straps. It includes a Pressure Regulator to ensure environmentally friendly, accurate and uniform spraying, offering 3 functions in one: - Adjustable at 1.5 bar (herbicides).- Adjustable at 3 bar (insecticides-fungicides).- Fully open for normal spraying, and decompression. Additionally it includes a Viton chamber seal, new stainless steel handle, high performance hose, 4 hollow cones nozzle as well as a complete set of nozzles.  Capacity: 20 Litres.

Maplin Extra Flexible Wire Red (priced per metre), at Maplins
•Reel Deal - Half price when bought as a full reel (See below)A very flexible wire ideal for test leads and as inter-connection wires which are frequently being moved.Purchasing information and Reel dealThis product is sold in units of 1 metre, up to a maximum length in 1 piece of 25 metres. Orders placed for a quantity of 25 units, or multiples of 25 units will be supplied on a reel; otherwise the cable will be supplied cut to length.

MBR3060PT 30A Schottky Barrier Rectifier, at Maplin
•Low power loss, high efficiency•High current capability•Low forward voltage drop•High surge capability•Guarding for overvoltage protectionA 30A Schottky barrier rectifier ideal for use in low voltage, high frequency invertors, free wheeling and polarity protection applications. It is supplied in a TO-247AD style case.

Fluke 175 True RMS Multimeter, at Maplin
Manual and automatic ranging•Display Hold and Auto Hold•Frequency and capacitance measurements•Resistance, continuity and diode measurements•Min-max-average recordingFor professional technicians worldwide there is one preferred solution: the precision, reliability and ease of use they find in Fluke 170 Series True RMS digital multimeters. This is the industry standard, with all the features you need to troubleshoot and repair so many problems in electrical and electronic systems. Fluke 170 Series digital multimeters give you True RMS voltage and current measurements, 6000-count resolution, manual and automatic ranging and provide frequency, capacitance, resistance, continuity and diode measurements. In addition, the Fluke 177 and 179 provide higher 0.09% basic accuracy, a digital display with analog bar graph and backlight. And the Fluke 179 delivers temperature measurements. Fluke 170 series multimeters are independently tested for safe use in CAT IV 600V/CAT III 1000V environments.

Easy Karaoke Machine with Camera, at Maplin
•Plays CD & CDGs + Includes 60 track disc•Built-in video camera to display your image on screen- karaoke song lyrics super imposed over your image•2 microphone sockets & LED Display read-out•Built-in 2 x 1 watt speakers•Microphone volume control & echo control•Auto Voice Control

Power Pax 65W Switched Mode AC/DC Fixed Voltage 24V Power Supply, at Maplin
•Power supply suited for CCTV, LED and other permanent electronic installations•24VDC 65W regulated output•Supplied bare wire for electrical installation •Fitted with a 2.1mm DC plug and 1.8m long output cord•Lugged base for permanent mounting, 4mm fixing holesA 24V power supply offering up to 65W of continuous output power supplied in a compact housing which features fixing lugs at either end allowing the PSU to be secured to any flat surface. This supply also comes with a fixed input lead helping to prevent accidental disconnection from the mains supply. All power supplies offered in this series are CE, LVD, EMC approved and also meet the latest ErP stage 2 requirements for energy efficiency

Replacement lamp for OPTOMA-EW400, at Maplin
•Complete projector lamp for the OPTOMA-EW400• Compatible with project manufacturer part code(S)-BL-FP240B / SP.8QJ01GC01• Expected lamp life of 2000 Hours• 120W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

8mm Panel Mount Orange with Chrome Bezel LED, at Maplin
A 12V, 8mm panel mounting LED with chrome bezel. The LED is supplied with a washer and locking nut . Has a reverse voltage of 5V, an 8mm diameter drilling hole and a thread size M8x0.75mm.

105A Tactile Switch, at Maplins
•A small tactile switch •PCB mount click-effect switch•Positive click action•Single pole, push-to-make non locking

Maplin Alkaline 9V Batteries 3 Pack, at Maplins
•Amazing value-for-money•Specially designed for high-drain applications•Advanced formula offers 10% higher capacity than standard alkaline batteries•Superb leak-proof technologyUsing the latest advanced battery technology, these batteries offer 10% higher capacity than standard alkaline batteries.

Cobra PMR Full Face Helmet Headset Kit, at Maplins
•Ideal for Motorbike users, motor-cross events, Skiing or just about anywhere you need to use radios and wear a helmet•Flat covered speakers for a snug fit inside the helmet•Waterproof press to talk (PTT) button control•Microphone designed to reduce road noise for clearer comms•2.5mm jack for Cobra and other PMR radios

Compatible Panasonic Camcorder Battery VWVBG130 7.2V, at Maplin
•Replacement battery for 7.2V Panasonic digital camcorders•1000mAh battery capacity•Dimensions: 36 x 32 x 24mm•Weight: 55g•Li-ion

Earlex SS125UKP Maxisteam Wallpaper Stripper 240 Volt, at Maplin
The Earlex SS125UKP Maxi Steam Wallpaper Stripper is ideal for the first time buyer or infrequent decorator as it machine is easy to use. The Earlex SS125UKP will remove all types of wallpaper - multi-layered, painted and even Artex. The Earlex SS125UKP is fitted with a powerful 2000 watt element that heats the water more quickly so that it will save energy and cost. This wallpaper steamer has a large 4 litre water capacity container, allowing up to 70 minutes of useage time, thus reducing the number of times that it has to be filled up. In addition, it only takes 12 minutes to for the steam to be ready to use. The Earlex SS125UKP has a built in exterior water level indicator allowing the user to see when a refill is necessary, this helps to not damage the steamer and prolongs its life. The system only uses water, making it environmentally friendly yet highly effective. All Earlex DIY steam wallpaper strippers have a cool-to-touch hose, overpressure safety valve, anti-discharge valve and anti-suckback valve, designed for user safety. Specifications: Element: 2,000 Watt. Usage time: 70 minutes. Steam up time: 12 minutes. Steam plate dimensions: 280mm x 203mm.

8W 100V PA Horn Speaker, at Maplin
•Black coloured ABS plastic speaker with adjustable bracket•8Wrms total power•Suitable for indoor or outdoor use•Metal bracket adjustable for any surface•Frequency range: 700 - 6000 Hz•Impedance: 8 Ohms•Dimensions: 88 x 88 x 105 mm

2x45V 625VA Toroidal Transformer, at Maplin
•High Quality Open Style Toroidal Transformer•Dual Primary / Secondary Windings•Thermal fuse fitted to each Primary•Very low radiated magnetic field•Supplied with mounting kit•UL Approved625VA Dual Primary (2 x 0-115V) Toroad

DIY Gamer Kit without Arduino, at Maplin
•Contains the versatile Arduino Uno development board •Learn how to program your own video games•Play your games using a classic gaming control layout•Add music and sounds to your games using the on-board buzzer•Takes around two hours to build•Note: The Arduino is not includedSpecial Features•Communicate with other players wirelessly using built in infrared link hardwareWhat can I play?The Gamer uses an LED matrix display making it excellent for playing games like Snake and Breakout. The types of games you can play on the Gamer are only limited by your imagination. Through the use of the Arduino software you can create your own game or you can take an example game and modify it to do something different. There are some example games available for download including Flappy Bird, Game of Life, Noughts & Crosses and more.What can I learn?The Gamer is designed to teach you about programming. The Gamer uses the Arduino Uno as the computer which will teaches you how to program in a language which is derived from C, one of the widest used programming languages.Can I invent with this board?The options that you are given when programming the Gamer are limited only by the creativity of the person creating the code. There are pins remaining unused on the Arduino leaving space for you to add your own hardware to the Gamer.

Himoto 1:18 Brushless Monster Truck (Mastadon Brushless), at Maplins
This small scale truck has all the key features of bigger 1/10th scale radio control trucksHimoto Mastadon Brushless ,1:18 Scale Monster Truck, ,Himoto introduces its newest 1/18 scale Mastadon Truck. This small scale truck has all the key features of bigger 1/10th scale radio control trucks such as shaft driven four wheel drive, durable differentials, oil filled shocks, and robust design. It's all packed into a truck that will fit in the palm of your hand. The Mastadon is also fully equipped with a 2.4ghz radio system, powerful 3700kv brushless motor, 18amp electronic speed controller, and a 7.4v 1500mah 25c continuous 40c burst rate battery pack. The compact monster truck chassis lets you take on other off-road vehicles in wheel-to-wheel action, allowing you transform your yard into a fun offroad course! Electronics: 2.4ghz Transmitter 2.4ghz Receiver 7.4v 1500mah 25C continuous 40C burst Battery 3700kv Brushless Motor 18A Brushless Electronic Speed Controller 1.1kg Precision Steering Servo, ,,Features: Molded protective gear cover Molded tub chassis with optimized weight distribution 4 oil-filled rebuildable shocks with progressive springs Special titanium anodized shock caps Fully independent double A-arm wishbone suspension Tough C-hub steering knuckles Tough and efficient 4WD shaft driven drive train Low friction ball raced bearing 4 high-traction multi-block tires Attractive 5 spoke wheels Factory-finished pre-cut body Front and rear molded bumpers Twin point steering with integrated servo saver,,Specifications: Length: 240mm Width: 190mm Height: 96mm Wheel Diameter: 68mm Wheel Width: 35mm Weight: 575g,,Required to Run: Four AA Batteries

Replacement lamp for TOSHIBA-56HM66, at Maplin
•Complete projector lamp for the TOSHIBA-56HM66• Compatible with project manufacturer part code(S)-Y67-LMP / 72514011 / 75008204• High Quality, High Brightness• Long Life If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Metal Film 0.6W 240k Ohm Resistor, at Maplins
•Ideal replacement for carbon film 1/4W, 1/3W or 1/2W types•Body size is the same as 1/4W types •Superior replacement to most metal oxide and thick film resistorsNote that to make up ‘odd’ values not stocked, resistor networks may be built and if all the resistors in the network have a 1% tolerance, then the tolerance of the whole network will still be 1% tolerance.

Replacement lamp for PHILIPS-LC 4500-17, at Maplin
•Complete projector lamp for the PHILIPS-LC 4500-17• Compatible with project manufacturer part code(S)-LCA3104• Expected lamp life of 4000 Hours• 100W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

WD 4TB My Cloud NAS External Hard Drive, at Maplin
•Keep your content safe at home without monthly fees•Access and upload your photos and videos anywhere•Easily transfer to and from Dropbox and other cloud accounts•Gigabit Ethernet and USB Connection•WD 4 TB My Cloud External NAS Hard Drive WDBCTL0040HWT-EESNSave everything in one place and access it from anywhere with computers, tablets and smartphones.Your own personal cloudWD 4 TB My Cloud allows you to keep all your content in one safe place at home or your office. No monthly fees. No limits.Centralize your media collectionStore and organize all of your photos, videos, music and important documents on your home or office network.Access from anywhereEnjoy your digital life from anywhere on your PC and Mac computers, tablets or smartphones with WD's file management app.Automatic file backup for all your computersEasily back up the files from all the PC and Mac computers in your home or small office.Flexible backup optionsEnjoy peace of mind with WD SmartWare Pro for PC users and Apple Time Machine for Mac users to protect your data.Expand your tablet and smartphone storageUpload photos and videos directly to your personal cloud from anywhere and free up space on your mobile devices.Connect to Dropbox and moreEasily transfer files between your personal cloud, Dropbox and other cloud accounts using the WD My Cloud mobile app.Increase your personal cloud capacitySimply attach a compatible USB 3.0 hard drive directly to the USB expansion port on the My Cloud drive and instantly expand your storage capacity.Transfer and access fasterGigabit Ethernet and a Dual-Core processor deliver blazing-fast file transfers and seamless remote access.Unleash your mediaSeamlessly stream your videos, photos and music to your connected TVs, media players, gaming consoles and other DLNA-certified devices.Password protection for privacyYour data is always safe and completely under your control. Protect your personal cloud from unauthorized access with password protection available for every user.Set up in minutesGet up and running in minutes with WD's rich web-based user interface for seamless, web-guided setup.Add an extra layer of protection for your filesYou can automatically make a second copy, or safepoint, of your My Cloud on your home or office network. With double-safe protection for all your media, you get ultimate peace of mind.Direct photo uploads from your camera with USB 3.0Simply connect your camera using the USB 3.0 port to quickly add all of your photos to your personal cloud.My Cloud personal cloud storage products work concurrently with multiple operating systems including Mac OS, Windows 8, iOS and Android with mobile apps.SOHOSave everything in one place and access it from anywhere with computers, tablets and smartphones.

Ring Automotive 2000W Pure Sine Wave Inverter, at Maplins
•Lower distortion rate than modified sine wave inverters•Replicates normal 240 volt mains supply•Compatible with all inductive and capacitive loads•Improved performance for audio and video equipment•2000W continuous power•4000W surge power (1 second)•Automatic alarm and shutdown protection against overload•Over temperature and low-battery conditions•Ideal for devices that cannot be powered by a modified sine wave inverterThe PowerSource range of professional inverters are the ideal choice for powering tools and equipment in demanding environments such as service vehicles, commercial applications and remote locations without a normal mains supply.

Eveready Soft Lite Low Energy Reflector 9W SES, at Maplin
•Energy Efficient•Excellent colour rendering•Long life: 10,000 hours•Instant start•Warm White 2700K

Bare Conductive Flashing 3 Card Set – Conductive Encounters, at Maplins
•Have fun creating three flashing LED greetings cards with out of this world alien designs•Use conductive paint to build a working circuit without any wires•Learn about electronics and conductivity•Components for three cards with battery, card and LED for each•Fun for ages 12+•Each card uses one 3V coin cell battery (provided)What do I get in this kit?This kit comes with everything you need for three amazing greetings cards. With flashing LEDs and striking alien designs, these are fun greetings cards that everyone would be happy to receive. The kit comes with 10ml of paint that allows you to paint your circuit directly onto the card. With a 3V coin cell battery, flashing LED and different design each for three very special cards.How do the cards work?These cards use Bare Conductive electrical paint to complete the circuits on the cards as well adding to the designs. Conductive, easy to use, water based and non-toxic, this paint is a great way to introduce and play with the ideas of electric conductivity. Conductive paint can be applied to a variety of surfaces other than card such as wood, textiles and some plastics. The paint dries at room temperature, and if you make a mess it can be removed with soap and water. How can conductive paint complete a circuit?Insulators like wood, card or fabric have very low electrical conductivity, so you cannot use them to carry electricity. However, metals, plasma and water carry electricity well. Conductive paint becomes more conductive when it dries. When dry, the paint has enough electric conductivity to complete a circuit, letting you power the LED. Conductive paint is a great alternative to acid etching, as it can be used without gloves and masks. Bare conductive electrical paint is not suitable for application onto bare skin.

LED Lenser F1 Torch, at Maplin
•A fixed focus lighting powerhouse pumping an astounding 400 lumens from it pocket sized casing.•Tactical styling with integrated anti-roll, interchangeable glass breaking front-ring and dual direction 360° pocket -clip•Energy efficient CREE Power+ LED Light Chip•Smart Light Technology (SLT) – Power, Low Power, Defence Strobe•Dynamic Switch ™ - Reactive single switch controls light options •Corrosion resistant gold plated contacts for better conductivity•Water and dust resistant. IPX54Ask a test pilot or racing driver to design a torch and this is probably what they would come up with. Modular in construction – so parts can be replaced where necessary - the F1 is a tour de force of engineering excellence. It unleashes an incredible 400 lumens of light with the explosive force of a fighter jet yet measures only 88mm and uses just one CR123A battery. The CREE Power+ LED, capable of blasting a bolt of light up to 100 metres, is of such high-strength that it has a specially-designed black ribbed section near the front to increase the available surface area for heat dissipation. It has gold-plated battery contacts inside to optimise energy transmission and these in turn are enclosed in an aircraft-grade aluminium barrel anodised to HIII military standard. The front of the torch has a removable stainless steel ring, which can be replaced with an optional Tactical Ring, that has the ability to smash through glass or ice, making this torch a perfect pocket option for military, security and police use. Weighing a mere 69g it is also ideal for outdoor backpacking and adventure activities where a strong light is needed without a bulky weight. A precision switch on the end cap allows the user to select from three Smart Light Technology light functions: Power, Low Power and Defence Strobe. The F1 is so small it fits into a shirt or overall pocket and has a clever two-way clip that can be turned 180 degrees and allows the light to be easily mounted on to a cap or sleeve .

Replacement lamp for PLANAR-PR3010, at Maplins
•Complete projector lamp for the PLANAR-PR3010• Compatible with project manufacturer part code(S)-997-3346-00• Expected lamp life of 3000 Hours• 180W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

DJI Inspire 1 Battery Heater, at Maplins
•Helps to exert the optimum battery performance by heating the battery to a suitable temperature (above 5°C) before flight•Enables the users to fly Inspire 1 in a more reliable way•Requires a tiny proportion of power from the flight battery to pre-heatThe performance of your Inspire 1’s Intelligent Flight Battery is subject to environmental factors. Low temperature will have adverse effect on the performance of Inspire 1 Intelligent Flight Battery. The Inspire 1 Battery Heater helps to exert the optimum battery performance by heating the battery to a more suitable temperature (above 5 ° C) before flight, enable the users flying their Inspire 1 in a more reliable way.Insert the Intelligent Flight battery into the Battery Heater compartment before take-off, as it requires a tiny proportion of power from the flight battery to pre-heat.Tech SpecRecommended Usage Temperature: -20 ° C to 5 ° CHeating Range: 30° C± 5 ° CPower: no more than 41.5WInput Voltage: 18-26.1V, DCInput Amperage: no more than 1.6ADimension: 62mm x 99mm x 115mmUsing the Battery Heater1. Ensure the battery is fully charged and powered off. Insert the battery into the Battery Heater compartment. 2. Turn the battery on and allow it to warm for 10-15 minutes (Actual operation time is subject to environment temperature. Longer or shorter times maybe required). Do not leave the battery unattended for extended period of time. 3. Turn the battery off and leave it in the Battery Heater for an additional 5 minutes (Actual operation time is subject to environment temperature. Longer or shorter times maybe required). The Intelligent Flight Battery is now ready for use.NoticeA 3-stage overheat protection mechanism has been incorporated into the Battery Heater’s design to prevent the battery from reaching temperatures that exceed its design parameters. To ensure that the battery does not overheat, the heater will be automatically deactivated at temperatures exceeding 30°C, with additional failsafe barriers in place at 50°C and 98°C.

ASUS AMD Radeon R7 250X 2GB GDDR5 PCI-E Graphics Card, at Maplin
•ASUS Dual Fan provides 2 X greater airflow whilst maintaining 3 X quieter performance•GPU Tweak utility provides real-time and intuitive tweaking•Acclaimed DIGI +VRM with Super Alloy Power technology delivers precise Digital Power and enhanced durability for stable overclocking•2GB GDDR5 Memory for the best gaming experience and the best resolution•HDMI•DVX11.2 lifelike graphics•CrossFire X Support - multi GPU technology for extreme performanceDual Fan Cooling2X greater airflow. 3X quieter.Twin optimized fans carefully selected by engineers drive 2X greater airflow while maintaining 3X quieter performance, combining enhanced cooling with a more pleasant gaming and computing environment.DIGI+ VRM with Super Alloy PowerSuperior Efficiency Reliability and PerformanceAcclaimed DIGI+ VRM has been applied via a power design that uses digital voltage regulators to minimize power noise by 30% and enhance power efficiency by 15%, widen the voltage modulation range, and improve overall stability and longevity by 2.5 times longer than reference. GPU Tweak with StreamingStream online instantlyGPU Tweak streaming tool that lets you share on-screen action in real time – so others can watch live as games are played. It's even possible to add to the streaming window scrolling text, pictures and webcam images.Real-time intuitive graphics tuning•Shows detailed specs and actual card status with GPU-Z•Sync GPU clocks and voltages for easier overclocking•Monitoring widget provides real-time detailed multi-parameter info•2D/3D switcher locks cards in 3D mode for higher benchmarks•Automatically checks and updates drivers and BIOS versions•Stream on-screen action to the web in full HDAMD Eyefinity™Broaden your gaming landscape across up to six independent displays simultaneously via DisplayPort or DVI connectivity. Now fully certified and supported by over a 100 games.AMD HD3DImmerse in stereoscopic 3D gaming and get up close and personal with your favourite stars while watching Blu-ray 3D. AMD HD3D is also designed for professionals who create complex visual effects and detailed data visualizations.Microsoft DirectX 11.2Brings new levels of visual realism to gaming on the PC and get top-notch performance.CrossFire SupportMulti-GPU technology for extreme performance.PCI Express 3.0Delivers double the bandwidth per lane of PCIe 2.0 for faster GPU-CPU communication.

Cooler Master Blizzard T2 Heatsink and Fan, at Maplins
•Patented Dual Loop™ design doubles heat pipe to CPU contact area and heat pipe performance•Patented CDC™ Continuous Direct Contact heat sink base for minimum thermal resistance•Snap-On fan brackets to quickly and easily install, remove, clean or replace the fan or heatsink•Versatile all-in-one mounting solution for all common Intel and AMD platformsThe Blizzard T2 offers far superior cooling performance compared to other dual heat pipe heatsinks thanks to CoolerMasters patented Dual-Loop™ heat pipe design. All 4 heat pipe ends are forming a continuous direct contact base to quickly and efficiently cool CPU Hotspots. Thanks to its universal mounting system, the Blizzard T2 fits on all common Mainboards. Snap-on fan brackets make installing and cleaning the heatsink quick and easy, and allow the installation of high performance or super silent fans.

Pifco Microfibre Cloth Pack of 2, at Maplin
•Pack of 2•2 x Microfibre cloths•For use with P29004 - 6-in-1 Steam Mop

Sylglas Anti-Slip Tape 50mm x 18m Yellow, at Maplin
Do you have problem steps, decking areas or pathways around the house where people can lose their footing? Areas like these can be particularly dangerous for the elderly, disabled or children, leading to serious injuries in some cases, if no action is taken. Self-adhesive, easily applied, can be used indoors or outdoors.Quick and cost effective.Can be applied to a multitude of surfaces.Available in black, yellow or clear. RECOMMENDED USES: Steps, patios, garage floors, decking areas, emergency staircases, apartment staircases and access ramps. Size 50mm x 18mColour Yellow

Maplin 9 Part Long Arm Star Key Set, at Maplin
•Heavy-duty set of star keys for a multitude of uses•Sizes range from T10 to T50•Supplied in a folding plastic holder with size markings•Made from chrome vanadium steel for maximum performance•Slip resistant coating for improved grip•Chamfered tips for easy entry into openings

Switched Brass BC Lampholder, at Maplin
Smart brass bayonet cap (BC) lampholder with 1½2" threaded base. The body is joined by a solid brass threaded collar and another threaded ring is provided for securing a lampshade. The base includes a screw terminal for an earth wire. This lampholder must be earthed, therefore a 3-core mains cable is required. Maximum rating 250W, complies with BS5042-T2.

Corsair RM850 Fully Modular 80+ Gold Quiet PC Power Supply, at Maplin
•80+ Gold-certified Efficiency - up to 92% efficiency, saves on your electricity bill.•Flat black, Low-Profile Modular Cables - Create a great-looking PC build.•Corsair Link Compatible - real-time monitoring of fan speed and power delivery.•Low-profile pump for easy installation and better airflow•Optimized for Silence - Zero Fan Spin to 40% Load, Ultra Quiet Fan when running.•5 year warranty & lifetime access to Corsair’s legendary technical support & customer serviceCorsair RM Series power supplies are fully modular and optimized for silence and high efficiency. Zero RPM Fan Mode means that the fan doesn’t even spin until the power supply is under heavy load, and the fan is custom-designed for low noise operation even at high loads. 80 PLUS Gold rated efficiency saves you money on your power bill, and the flat black cables are fully modular, so you can enjoy fast, neat builds. And, like all Corsair power supplies, RM Series is built with high-quality components and is guaranteed to deliver clean, stable, continuous power. Connect it to your Corsair Link system and you can even monitor fan speed and +12V current directly from your desktop (additional cable required.)Specification:Total Power: 850WAC Input: 100 - 240VInput Current: 12A - 6AFrequency: 47Hz - 63Hz+3.3V Max Load 25A, Max Output 150W+5V Max Load 25A, Max Output 150W+12V Max Load 70.8A, Max Output 850W- 12V Max Load 0.8A, Max Output 9.6W+5Vsb Max Load 3A, Max Output 15WModular cable management: Fully modular Flat Cables Number of cables: 13Motherboard cable (20+4 pin): 1 @ 610mm4+4-pin (CPU, works as either 4 or 8-pin): 2 @ 650mmPCIe 6+2 pin (GPU): 6 @750mm4-pin Peripheral power connector: 8SATA 5-pin connector: 10Floppy power: 2

Monitor Cable Mini DisplayPort Male to HDMI Female, at Maplins
• Convert Mini DisplayPort to HDMI • No extra drivers needed when plugged in • Supports plug 'n' play for ease of use • HDMI resolution of 1920 x 1080 • 2 Channel audio function • Compliant with HDMI 1.3a • Compatible with Win XP, Vista, 7 and Mac OS X v10.5 or laterThe Mini DisplayPort to HDMI Adapter enables you to connect any HDMI interface embedded device (Monitor, Projector, TV) with a Mini DisplayPort interface (desktop, laptop). Not only does it convert the Mini DisplayPort signal to HDMI but it also sends the audio through the HDMI lead so you can watch movies on your TV or Projector from your Laptop or computer. This little device lets you connect your device to any HDMI TV, monitor or projector with ease. This means you can run two screens at once or use your device for presentations with a normal projector. This adapter can display 1080P resolutions or 1920 x 1200 dpi. Mini Display Port is also knows as MiniDP. These MiniDP ports can be found on many Macs, Laptops and Tablets plus some graphics cards. Please check your device manual for compatibility information.

Maplin Website really does have something for everyone, and provides an incredible range of top-quality brand-names at low, low prices!

• Buy wireless products from Linksys, D-Link, NETGEAR, TRENDware, Hawking Technology and more - Maplin has a huge range.
• Plasma televisions from Panasonic, Pioneer, Samsung, Philips, Daewoo Electronics …
• Maplin Desktop PC Memory Upgrades, Printer Memory Upgrades
• Projection TV's from Hitachi, Panasonic, Philips, Apex Digital … Maplin has literally hundreds of televisions to choose from.
• TVs, Audio, Home Theater, DVR, DVD Players/Recorders, VCRs, A/V Cables, Remote Controls
• Plasma TV's from Maplin feature some of the best prices available - buying a plasma TV from Maplin is money wisely spent!