Maplin Electrical is one of the UK's leading Electrical retailers, offering the most competitive choice of mainly branded, quality products at consistently the lowest prices in the local market. The core range of Maplin products include TV, video, audio, Cooking, MDA, Small domestic appliances, Communications, Multimedia, Electronics and New technology accessories. Maplin Stores are unrelated to the Dixons Stores Group - which includes Dixons, Currys, PC World and The Link.

Monitor Cable DVI Male to VGA Male 3m, at Maplin
• DVI to VGA PC monitor connection cable • Male DVI-A to male 15-pin type • Double-shielded, fully-fired cables for interference-free picturesThis cable is used to allow a DVI (with analogue output) graphics card to be connected to a VGA monitor or vice-versa. Please note that this cable will not covert a digital signal to an analogue signal, it is only designed for use with analogue.

ATC NiMH High Capacity Rechargeable 2000mAh AA Batteries 4 Pack, at Maplins
•High capacity NiMH rechargeable batteries•Recharge up to 1000 times•0% mercury, 0% lead, 0% cadmium•No memory effect

Replacement lamp for SANYO-PLC-XU350, at Maplin
•Complete projector lamp for the SANYO-PLC-XU350• Compatible with project manufacturer part code(S)-610-343-2069 / POA-LMP131• Expected lamp life of 2500 Hours• 225W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Heavy Duty Red LED Mains Tape Light 12M, at Maplin
•Heavy duty tape light with 60 LEDs per metre•Provides a wide 120 degree light•Can be cut and re-joined as required•Highly flexible•Ideal for building outlines, homes, shops, bars and nightclubsThis super-bright IP44 rated Heavy Duty Tape Light has 60 LEDs/m encased in a white epoxy resin coating to protect the tape. With a depth of just 6 mm and only 10 mm wide it will fit into many unusual places. The LEDs produce a wide 120 degree light which gives a reflected glow similar to that of neon. The tape can be cut or joined using the available accessories. The tape is highly flexible and is the ideal fixture for defining building outlines or for many uses in homes, shops, bars and nightclubs.

Brother LC1240Y Yellow Ink Cartridge, at Maplin
•Original Brother consumable•Yellow•Approximately 600 pages (ISO/IEC 24711)•Compabitble with DCP-J525W, DCP-J725DW, DCP-J925DW, MFC-J430W, MFC-J625DW, MFC-J6510DW, MFC-J6710DW, MFC-J6910DW, MFC-J825DW, MFC-J5910DW,Brother original supplies maintain top quality results & offer great value for money. Brother employ precision engineering in the development of ink. These inks are specially designed to give you high quality results from your Brother printing technology every time.

60w MP60 Travel Inverter - Single Socket, at Maplins
•Flexible design to suit different vehicles•Compact & lightweight allows it to be easily stored•For recharging mobile phones and other small wattage appliances12v DC - 240v AC, 60w MP60 Travel Inverter - Single Socket60w of power ideal for recharging mobile phones and other small wattage appliancesMax power rating (5 mins): 60wContinuous power rating (4 hrs): 45wPeak power rating: 120wNo load current draw: 0.1AWaveform: MSWPower connection: DC PlugWeight: 0.25Kg

4081 CMOS Logic HCF/HEF, at Maplins
•Industry standard CMOS 4000 series device•Quad 2-Input AND Gate•Supports power supply voltages of up to 15V and rail output swings•Ideal for hobby, industry and automotive applications•Used in a wide variety of circuit applications

2x50V 800VA Toroidal Transformer, at Maplin
•High Quality Open Style Toroidal Transformer•Dual Primary / Secondary Windings•Thermal fuse fitted to each Primary•Very low radiated magnetic field•Supplied with mounting kit•UL Approved800VA Dual Primary (2 x 0-115V) Toroad

Replacement lamp for PLUS-U3-1100Z, at Maplins
•Complete projector lamp for the PLUS-U3-1100Z• Compatible with project manufacturer part code(S)-28-390 / 28-631 / PU31080LP• Expected lamp life of 1000 Hours• 130W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Veho M1 Portable Speaker Black, at Maplins
• 2.4 W output with resonant chamber to improve bass quality• Integrated 3.5mm jack cable connects your smartphone,tablet or MP3 player• Lithium ion battery provides up to 8 hours of playback from a single chargeAdd some volume to your music, with the Veho M1 portable speaker. This palm sized speaker is small enough to carry in your pocket, perfect for those limited on bag space. A resonant chamber in the centre of the speaker enhances bass tones when fully extended, adding extra depth to your music. How long does it take to charge and how long can I use it for?Any powered USB port will charge the speaker within four hours. Once fully charged you can enjoy your favourite playlists and podcasts for up to eight hours continuously. You will never need to fuss over battery life with the Veho M1.What devices are compatible with this this speaker?Connect you iPod, iPhone, smartphone, tablet, PC and laptop or MP3 player via a 3.5 mm jack cable integrated into the speaker. Now you can enjoy great sounding movies, music and games across all your devices around the home.How loud is this speaker?2.4 W of power pushes out an impressive level of volume for a speaker so small. This is best suited for small rooms or environments where there isn’t a lot of background noise. A frequency response of 100Hz-20kHz ensures a punchy bass without drowning out higher pitch tones. Where a little extra bass is required, extending the resonant on the chamber will bring more bass out of your music.

Behringer X1622USB Xenyx Small Format Mixer, at Maplin
Behringer X1622USB Xenyx Small Format MixerBehringer X1622USB Xenyx Small Format MixerThe X1622USB features four XENYX-fueled mic inputs with channel Inserts, 'one knob' compressors and 3 band British style EQs with a sweepable, semi-parametric mid frequency band. The four stereo line level channels offer enhanced fine-tuning via 4-band EQ, which is extremely handy for adjusting critical keyboard midrange frequencies. Aux 1 Sends are switchable (pre- or post-fader) and individual channels can be assigned to two subgroups for mixing flexibility.Premium ultra-low noise, high headroom analog mixer4 state-of-the-art, phantom-powered XENYX Mic Preamps comparable to stand-alone boutique preamps4 studio-grade compressors with super-easy "one-knob" functionality and control LED for professional vocal and instrumental soundNeo-classic "British" 3 band EQs with semi-parametric mid band for warm and musical soundNew studio-grade FX processor with 16 editable presets including reverb, chorus, flanger, delay, pitch shifter, multi-effects, Tap function and storable user parameter settingsBuilt-in stereo USB/Audio Interface to connect directly to your computer. Free audio recording, editing and podcasting software plus 150 instrument/effect plug-ins and ultra-low latency driver downloadable at www.behringer.comChannel inserts on each mono channel for flexible connection of outboard equipment2 aux sends per channel: 1 pre/post fader switchable for monitoring/FX applications, 1 post fader (for internal FX or as external send)Clip LEDs, mute, main mix and subgroup routing switches, solo and PFL functions on all channels2 subgroups with separate outputs for added routing flexibility; 2 multi-functional stereo aux returns with flexible routingMain mix outputs with 1/4" jack and gold-plated XLR connectors, separate control room, headphones and stereo rec outputsControl room/phones outputs with multi-input source matrix; rec inputs assignable to main mix or control room/phones outputsLong-wearing 60 mm logarithmic-taper faders and sealed rotary controls"Planet Earth" switching power supply for maximum flexibility (100 - 240 V), noise-free audio, superior transient response plus low power consumption for energy savingRack mount brackets included for ultimate flexibilityHigh-quality components and exceptionally rugged construction ensure long life

FTDI Interface Expansion Module for Raspberry Pi, at Maplin
•One standard USB type A plug to connect to the host•External power input connector available to supply external downstream USB ports•Support for USB suspend and resume•UART data transfer rates from 300baud to 12Mbaud at 3.3V TTL levels•Synchronous serial (MPSSE) data rates of up to 30Mbps on JTAG, SPI and I2C•Defaults to two independent UART interfaces•All I/O pins are 5V safe•UHCI/OHCI/EHCI host controller compatible•On board EEPROM 93LC56 for FT2232H configuration•USB 2.0 high speed compatibleThe Interface Expansion Module is a USB HUB and USB to dual channel multi interface converter module designed for Raspberry Pi. It utilises an FT2232H USB to UART/MPSSE IC, along with a GL850G USB hub controller IC. The FT2232H based RPi HUB module is a USB to UART/245FIFO/SPI/I2C/JTAG/GPIO interface expansion module targeted at connecting to Raspberry Pi computer to expand the number of interfaces. However, it is not limited to this application. It can also be used as a HUB device or an FT2232H evaluation module. The module has a USB 2.0 high speed HUB chip which supports up to three external downstream USB ports. This module utilises the GL850G USB 2.0 HUB controller which provides a low cost and widely used USB 2.0 HUB solution, to provide up to 4 downstream USB ports. The GL850G is a single chip USB hub solution. The GL850G is a full function solution which supports both Individual/Gang power management modes and two colour (green/amber) status LED.

TP-Link 2.4GHz 8dBi Indoor Omni Directional Antenna, at Maplins
•8dBi Omni-directional operation boosts your signal to a higher range•Very easy to install, no software required•RP-SMA Female connector, works with device with RP-SMA Male connectorIndoor omni-directional antenna TL-ANT2408CL operates in the 2.4-2.5 GHz band and provides 8dBi omni-directional operation, which largely extends the wireless range and delivers much better wireless performance. The antenna offers the RP-SMA Female connector guaranteeing wider compatibility with most of the wireless equipments. Replacing your wifi antenna with TL-ANT2408CL will significantly increase the range and strength of your wifi signal. This quality built omni-directional antenna is a direct replacement for the antenna that comes standard with your router, access point. Because it is omni-directional, no aiming is equired - it can send and receive wifi in all directions.Installation is very easy - just detach your device's factory antenna and attach our booster antenna and you'll experience an instant increase in signal coverage and stability. Please note that the increase in signal strength depends mostly on your router or adapter; upgrading the antennas helps but the signal cannot transmit or receive at a level that your modem or adapter does not have.

2-Power CBI3168A Laptop Battery - Main Battery Pack 10.8V 5200mAh 58Wh, at Maplin
Laptop, Main power battery for portable computers•Lithium ion, Newer type of rechargable, giving best performance for a rechargable.•EAN: 5055190130124•Equivalent Part Number: GRAPE32•Number of cells: 6•Capacity: 5200.0mAh•Voltage: 10.8VMain Battery Pack 10.8V 5200mAh 58Wh

Kauden Snap in Brush Module – 25x50mm Black, at Maplin
• Fits 25x50 mm aperture for use with Kauden Modular faceplate system• Flame Retardant • Ideal for Audio Visual applications • Black finishBrush Modules simply snap into any Kauden faceplate and are commonly used to hide Audio Visual cables behind walls and so giving a clean appearance to your home rather than bundles of wires hanging down the wall or trailing around in the living room. Two plates are usually installed, one for entrance and the other for the exit of cables. Commonly these are at the top and bottom of the wall where the equipment resides. NOTE; They are meant to stand alone in their own faceplate and not intended for use alongside other modules in the same faceplate or alongside other wall sockets in the same channel where hazardous voltages may be accessible through the Brush Module.The Kauden modular faceplate system is a highly flexible way to customise your signal and data outlets to your needs. Slot in the interchangeable modules to the blank faceplates to create the perfect out let for your connectivity. Ideal for either home or office needs. A wide range of modules and faceplates are available. Quarter blanking plates are also available for faceplates with spare space.

Leitz Case with Stand for iPad Mini - Black, at Maplin
•Protects the back of your iPad mini, no scratches, no dust, no dirt •Sets an ergonomic viewing angle with the integrated two-position stand in horizontal and vertical direction •Rubber elements on the stand ensure effective grip •Full access to all sensors, connections and controls•Compatible with the original iPad mini smart cover •Distinctive Leitz design in high-gloss white and silky matt black with green coloured highlightsHardcover protection for the back of your iPad mini. The integrated two-position stand lets you set perfect viewing angles in horizontal and vertical orientations. Make your iPad mini complete!

LCD 1x8 Black Module, at Maplins
•4 and 8 Bit parallel interface using HD44780 and HD44100 protocols•High contrast ratios•Excellent viewing angles•Ideal for low cost applications, hobby electronics or replacing faulty screensAlphanumeric LCDs, which is supertwist. LCD has black characters on a green/yellow background.

Maplin Single Phono Composite Cable 1.5m, at Maplin
• Ideal for use with Televisions, Freeview and Freesat boxes, and CCTV systems.• 2 pole Phono terminal with positive and ground contact• 75O coaxial cable for analogue composite video signal• Gold-plated connectors• Durable and highly flexible outer jacket• 5 Year WarrantySingle Video Phono is also known as an RCA connection and carries a full colour analogue composite video signal. Composite video is found on standard definition TV’s and their AV equipment, such as VHS/DVD recorders and Satellite/cable boxes.The Maplin Range – Premium construction and specification, with marketing leading cable technologies.The Maplin Cable range delivers the latest technology first and foremost, ensuring compatibility with the latest hardware standards.Our Maplin cables feature fully wired connectors and shielded cables where required throughout the range, delivering high fidelity audio and video signals across a vast range of connectors and dedicated adapters.The Maplin cable range features hard wearing cable construction, with colour-coded, compact connectors available for almost any use. All Maplin cables are quality assured, with a 5 year warranty across the range.

HDMI Male to HDMI Female Swivel Adapter, at Maplins
• Swivel adapter allows HDMI connections to be flexibly made where space is limited • Gold plated connectors • Fully shielded • Full HD support up to 1080p and beyond

2-Power PTH0125A Power tools Battery - Power Tool Battery 14.4V 2000mAh, at Maplin
Power tools, Power battery for drills, etc•NiMH, Newer type of rechargable•EAN: 5055190135723•Equivalent Part Number: A9262•Capacity: 2000.0mAh•Voltage: 14.4V14.399999618530273

Weller SI175 Marksman Soldering Iron 175 Watt 240 Volt, at Maplin
Weller Marksman Soldering Iron is a heavy-duty soldering iron for the professional user and light industrial operator. Soldering iron has a thermoplastic handle designed for comfort and a safe grip and all connections are mechanically and electrically secure. Supplied with 3-pin plug and conforms to European standards. Specifications:Watt: 175 Watts.Power input: 230 Volts.

Yellowstone Flameless Cook Flask, at Maplin
•Lightweight, safe and portable alternative to a gas stove•Ideal for outdoor enthusiasts, mountaineers, backpackers, hikers, campers, scouts, guides, picnics, events, festivals, day trips etc.•Create a hot drink or meal with the minimum of fuss and in safe conditions, heat and cook liquid or food using the water activated heat pack•No need for gas, petrol, or dangerous fuels to create heat, making it far safer and simpler than other current cooking methods•Can be used inside a tent or confined space, as it does not give off any toxic or unsafe emissions and importantly does not produce carbon monoxide•Environmentally friendly option to gas or charcoal•Don't forget extra heat packs - Choose from 10x20g pack (Maplin Code: A71TC) or the higher power 10x50g packs (Maplin Code: A70TC)400ml medical grade stainless steel inner cooking flask which is robust and easy to cleanHeat resistant plastic outer box with airtight locking lid for safe handling when in useNeoprene sleeve prevents transfer of heat to surrounding area and provides safe handlingReady to use, supplied with one Super Power (20g) heat packFull easy to follow instructions included, its the new way to cook outdoors!

Spare Camera and Gimbal Unit for the DJI Inspire 1 Drone, at Maplins
•Compatible with the DJI Inspire 1 Drone •Record in 4K, giving you an Ultra-HD resolution for clearer videos and awesome aerial photography shots•Three-axis gimbal giving you a more accurate rotation of the cameraA spare camera and gimbal for if yours break. The Ultra-HD 4K camera gives you a maximum video recording resolution of 4096 x 2160p at 25 frames per second (fps). This gives you a fantastic looking picture as you soar through the skies. For still photography, the camera boasts 12.4 megapixels giving you the capability of high quality shots for those sweeping landscapes.

Trend DWS TF6 6in Diamond Taper File, at Maplin
The Trend 6in Diamond taper file is an exceptionally versatile multi-purpose sharpening tool suitable for woodworking, gardening and domestic tooling. Ideal for woodturning tools, Monocrystaline diamond allows fast, clean stock removal. Precision made with flat top and convex back blade. Size: 300mm (6in).Grit: 600.Micron: 25.

3-Channel 2.4GHz Nemesis Helicopter, at Maplin
•Large scale 72cm length makes the Nemesis the ultimate gift•3D multi directional controls •Very easy to fly•Suitable for outdoor use•Spare rotors included•LED lights•With gyro for added control•Requires 6AA batteries (not included)•Spares replacement pack available to buy ( Maplin order code A32TN)The Nemesis helicopter is a three channel outdoor helicopter which means you get three planes of movement, up and down, left and right, and forward and back. This slick helicopter has a hard robust shell to protect all the gears and motors so they can withstand overconfident flying and coming into contact with the ground several times. The controller comes with an LCD display highlighting trim settings and power output levels

3.5mm Stereo Jack to Jack Cable 0.5m, at Maplins
•Nickel plated connectors•Fully screened cable•Durable PVC Jacket•Cable strain relief to protect the cable3.5mm stereo plug to 3.5mm stereo plug (as used by most portable audio devices) with screened audio cable.

IRWIN Record 136/5 T Bar Clamp 1200mm (48 - 42in) Capacity, at Maplins
IRWIN Record 136/5 T Bar Clamp is a robust clamp for heavy-duty work which offers the facility of permanent fixing to a workbench. T-bar section in cold drawn steel gives extra strength and resistance to bending. Extra long head with machined slides is extremely durable. The IRWIN Record 136/5 T Bar Clamp has the following specifications:Bar Length: 1200mm (48 inch).Capacity: 1050mm (42 inch).

Eagle 100 V Line Horn Speaker (Power RMS 25), at Maplin
Eagle 100 V Line Horn Speaker (Power RMS 25)Eagle 100 V Line Horn Speaker (Power RMS 25)

Netgear 1200Mbps Powerline Kit with Single Gigabit Ethernet Port, at Maplin
•1200Mbps powerline speed•Perfect for connecting smart TVs, streaming players & game consoles•Ideal for 4K HD streaming & lag-free gaming•Add up to 16 adapters to expand your network & lag-free gaming•Pick-a-plug LED for highest possible performance•Sets up in minutes, no need to install software•Secures the network connection with the touch of a button•Energy saving -- powers down when not connectedPowerful Gigabit Wired ConnectionUse your existing electrical wiring to extend your Internet access to any room in your house. Just plug the Powerline 1200 into any electrical outlet then plug in your new network connection. It's that easy. With a 1200Mbps speed and Beamforming, the Powerline 1200 is perfect for connecting smart TVs, streaming players, and game consoles.Get Connected with PowerlineExtend your internet access to any power outlet. NETGEAR Powerline is the easiest way to extend your internet connection without running long wires. Just plug into any electrical outlet then plug into your existing network connection and you have a wired network using your electrical wiring. It's that easy!4K Video? No Problem.NETGEAR Powerline adapters are lighthning fast and can deliver over 1Gbps speeds with the latest Homeplug AV2 technology. Streaming 4K video, online gaming, or home security video monitoring. No problem we got you covered!

2-Power DBI9977A Camera Battery - Digital Camera Battery 3.7V 770mAh, at Maplins
Camera, Power battery for cameras•Lithium ion, Newer type of rechargable, giving best performance for a rechargable.•EAN: 5055190139004•Equivalent Part Number: BP88•Capacity: 770.0mAh•Voltage: 3.7V3.700000047683716

12 V Filament Bulb 360 mm Gooseneck with BNC Plug, at Maplin
12 V Filament Bulb 360 mm Gooseneck with BNC Plug12 V Filament Bulb 360 mm Gooseneck with BNC Plug12 V filament lamp fitted in the end of a 360 mm flexible black gooseneck. The gooseneck is fitted with a standard BNC male plug.

Replacement lamp for PANASONIC-PT-AE400, at Maplin
•Complete projector lamp for the PANASONIC-PT-AE400• Compatible with project manufacturer part code(S)-ET-LAE4000• Expected lamp life of 2000 Hours• 170W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Replacement lamp for SAMSUNG-HL-S5065W, at Maplin
•Complete projector lamp for the SAMSUNG-HL-S5065W• Compatible with project manufacturer part code(S)-BP96-01472A• Expected lamp life of 2000 Hours• 132W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Replacement lamp for EPSON-ELP-3000, at Maplin
•Complete projector lamp for the EPSON-ELP-3000• Compatible with project manufacturer part code(S)-ELPLP01• Expected lamp life of 6500 Hours• 190W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

PNY VCNVS315DP-PB Graphics Card nVidia Quadro NVS 315 1GB PCI-E DisplayPort, at Maplin
• DISPLAY PORT 1.2 SUPPORT• VERSATILE DISPLAY CONNECTIVITY OPTIONS• NVIDIA ENTERPRISE MANAGEMENT TOOLS• LOW-PROFILE AND FLEXIBLE FORM FACTORThe NVS 315 delivers exceptional flexibility and compatibility that lets you get the most from your existing display infrastructure. Drive all your DisplayPort, DVI, and VGA displays, regardless of display connectivity or chassis size. Even power two ultra-high resolution displays simultaneously at up to 2560x1600 using the NVS 315's proven combination of hardware and software. Gather insights faster from an expanded workspace of multiple high-resolution displays and get three times more graphics cores than previous-generation NVS solutions for significantly improved visualization. Plus, take advantage of 1 GB of on-board frame buffer memory to interact with more visually compelling content on larger, high-resolution displays. NVS boards are designed with simplified IT management in mind, including advanced tools that make integrating and maintaining a large scale PC deployment fast and easy. Plus, they allow remote query and control of graphics and user display settings for systems spread across installations.CPUNumber of Cores : 48 GPUChipset : NVIDIA Quadro NVS 315 DisplayMaximum Resolution : 2560 x 1600 PixelsMemoryMemory : 1024 MB DDR3 Designation : DDR3 Memory Width : 64 bitInterfaces/PortsVideo Card Bus Type : PCI Express DisplayPort : 1 x DisplayPort PhysicalForm Factor : Single Slot (Low Profile) In The Box : PNY VCNVS315DP-PB Graphics Card, Low-Profile Bracket, 1 x DMS59 to DP, Drivers, Installation Guide Additional SpecificationsModel Name : VCNVS315DP-PBProduct Family : Quadro NVS 315Product Type : Graphics CardVideo Card Bus Version : 2.0 x16

Replacement lamp for SANYO-PLC-SU31, at Maplin
•Complete projector lamp for the SANYO-PLC-SU31• Compatible with project manufacturer part code(S)-610-293-2751 / POA-LMP35• Expected lamp life of 2000 Hours• 200W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

EtherCON CAT6 Chassis D Type Black, at Maplin
•CAT6 compliant - data rate up to 10 GBit/s •CAT6 performance - fast data transmission and high bandwidth applications •CAT6 specifications according TIA / EIA 568B, ISO / IEC 11801, EN 50173 •IP65 - Dust and waterproof in mated condition •Shielded system - high noise immunity and EMI protection •Push Pull mating - secure and proven locking system •Ground lead jumper on panel connector with selectable grounding option •Gas-tight IDC termination without toolThe etherCON CAT6 D-shape panel connectors with black metal housing and secure latching system offer a tool-free and gas-tight IDC termination, which makes cable assembly easy and fast.

RADIUS BL10 SMART CORD, at Maplin
The BL-10 cord is the solution to a common problem of not being able to connect headset and telephone. The BL-10 cord will work with virtually any phone providing greater convenience.Works with most desk phones including IP hard phones; Microphone amplification to boost transmit levels when connecting to low transmit volume phone systems.; Simple slide adjustment for easy setup.

(Used) Sennheiser PXC 250 On Ear Headphones Black, at Maplin
•On ear design for comfort•Wired connection for maximum compatibility•NoiseGard active noise cancellation and passive attenuation to eliminate background noise•1.5 m long cableSpecial Features•Includes a convenient carry case•Foldable for easy storage•Includes an inflight adapterHow does the noise cancellation feature work?The Sennheiser PXC 250-II are wired noise cancelling headphones with a closed over ear design to ensure attenuation of background noise so you can enjoy your music in peace. These headphones also include active NoiseGard technology designed to cut down the impact of ambient noise. NoiseGard enables you to further block out low frequency ambient sounds for up to 50 hours using a single AAA battery.What products are these headphones compatible with?The headphones use a wired 1.5 m long cable with 3.5 mm jack input making them compatible with a wide range of smartphones, tablets, music players and portable gaming systems. The included inflight adapter also makes these headphones compatible with any airline service, allowing for comfortable use on long flights.How good is the sound quality for these headphones?Designed for all types of music, The Sennheiser PXC 250-II headphones closed feature helps to deliver clear and well defined bass. Combined with the noise cancelling and integrated volume control functions, these headphones will provide a crisp, clear sound. They’re also designed for travel with their lightweight folding design. To close they fold 90 degrees for simple, safe storage and can be slipped away into the included carry case for added portability.

Silicon Washers 50 Pack, at Maplins
•Silicon oscillation washers•Ideal for fixing between the hard disk and screws•Prevents oscillation and noise•Thickness: 2mm / diameter: 10mm•50 pcs included

Replacement lamp for OPTOMA-DX319, at Maplin
•Complete projector lamp for the OPTOMA-DX319• Compatible with project manufacturer part code(S)-BL-FU185A / SP.8EH01GC01• Expected lamp life of 3000 Hours• 185W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Replacement lamp for 3M-MP8745, at Maplin
•Complete projector lamp for the 3M-MP8745• Compatible with project manufacturer part code(S)-EP1635 / 78-6969-8919-9• Expected lamp life of 2000 Hours• 190W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Altai Treasure Seeker 4 Professional Metal Detector, at Maplin
Altai Treasure Seeker 4 Professional Metal DetectorAltai Treasure Seeker 4 Professional Metal DetectorFeature packed metal detector that with an LCD display giving a visual indication of what has been found. The detector can discriminate between gold, silver, ferrous and aluminium metal. The unit has a 3.5 mm headphone socket, volume control, touch control sensitivity, notch and discrimination controls. The detector has a waterproof 200 mm coil and an adjustable arm for comfort and ease of use.

Label The Cable Tube Black 2m 1 Pack, at Maplin
•Can be cut to length with scissors•Subsequent attachment to cables possible•No disconnection of devices•Soft polyester fabric•Self-closing•Diameter adjusts itself (2.5 – 4 cm)•Reusable •Dimensions: total length about 2 m, diameter 2.5 – 4 cmWith LTC CABLE TUBE, cables are bundled faster than data flows through them. The lateral opening of the self-closing polyester fabric also makes subsequent attachment of the cable tube possible without disconnecting the devices LTC CABLE TUBE adjusts its diameter (2.5 – 4 cm) to the contents, and the later removal or addition of individual cables is no problem. In addition, cutting the high-quality tube to length is child’s play. LTC CABLE TUBE is RoHS-compatible and has been temperature-checked from -50 to +150 °C. It is suitable for deployment in extreme locations, but is also at home in every living room.LTC CABLE TUBE is suitable for - bundling all types of cables

3 Channel Helicopter with Gyroscope Stabilizer Replacement Bearing (4x1.5x2), at Maplins
•Replacement bearing for 3 Channel Helicopter with Gyroscope StabilizerThe power of flight all from a little box offering challenging manoeuvres, daring ground hugging flight or just taking off and landing. If you''ve never had the opportunity to try your hand at flying a radio controlled aircraft then this package gives you everything you need to get started.

Replacement lamp for NEC-LT220, at Maplins
•Complete projector lamp for the NEC-LT220• Compatible with project manufacturer part code(S)-LT60LPK / 50023919• Expected lamp life of 2000 Hours• 220W Lamp Wattage If possible please follow the user manual for your projector model. & nbsp; How to take the lamp out of the projector : & nbsp; 1. Turn the projector off by pressing the Power button 2. Allow the projector to cool down for 30 - 45 minutes 3. Disconnect the projector from the power cable 4. Unscrew the screws on the lamp compartment cover, lift and remove 5. Unscrew the screws on the lamp module 6. Lift up the handle on the lamp and pull the lamp out slowly and carefully & nbsp; How to replace the bulb on the lamp & nbsp; Always use the appropriate tools to uninstall and install the bulb. In most cases you will only require standard screwdriver. & nbsp; Once the old lamp has been removed the new lamp can be installed ; & nbsp; 1. Place the new lamp into the open lamp compartment of the projector 2. Ensure the lamp is in the same position and orientation as the old lamp before it was removed 3. Press the lamp into the projector firmly to ensure the lamp and power connector are seated securely 4. Tighten any fixing screws where present 5. Replace the lamp compartment cover and replace the fixing screws 6. Reset the lamp timer & nbsp; On some projector models there is a need to change a setting on the projector so the projector knows there is a new lamp installed. This is only the case on some models, please refer to your user manual. & nbsp; Important: & nbsp; Do not touch the glass area of the lamp with bare hands. & nbsp; Natural oil from your hands can seriously impact on the performance of the unit or cause the lamp to shatter when it reaches very high temperatures. & nbsp; Use a dry cloth to clean the lamp if it was accidentally touched.

Prestigio Multiphone 5450 DUO Mobile Phone (Used), at Maplin
•Android 4.1•Dual Core 1.2 GHz CPU•SIM Free and unlocked•Great connectivity - stay in touch with everything using high speed Wi-Fi and webcam for video calls•Stand out in the crowd - 4 different colour rear covers included!•Uncompromising quality•Advanced technology and stylish designStay in the light with your smartphone – its bright colours will define your positive mood! Choose one of the stylish and bright covers by Prestigio and live your life in bright colours! This smartphone definitely stands out in the crowd!Paint your dreams brightly here and now with the Prestigio MultiPhone 5450 DUO – you will find 4 coloured rear covers inside the box. Be different and change your style whenever you want! This smartphone combines an exquisite design with outstanding performance. It provides a powerful 1.2 GHz processor, which helps to load your favourite applications quickly. This collates all of the social networking, mail and instant messaging onto one screen. Smooth and well-balanced as it is, the MultiPhone 5450 DUO will definitely give you a great experience.Fast Wi-Fi will let you be connected to all that matters in your life. Find your way with GPS navigation and location based services and chat with the friends via mobile social networking.Be DifferentWith the MultiPhone 5450 DUO you can now add bright colours to your daily routine! Just open the box and find 4 additional colour rear covers inside! Experience its seamless form and rubber coating material and enjoy using this smartphone. Besides, you can easily change its appearance.Perfect PerformanceRunning a 1.2 GHz dual-core processor, the MultiPhone 5450 DUO solves any task, no matter how complex it is. Play your favourite games, use office applications, surf online and watch HD-quality videos — do it simultaneously!Android 4.1The simplicity and speed of Jelly Bean is taken to a different level – a completely new camera that’s beyond smart, a new form of typing that helps you power through your messages and much more.Stay TunedListen to your favourite music with the built-in player, featuring support to all the most common formats and the option to create playlists. Connect earphones to the standard 3.5 mm jack, download favourite collections of albums and songs, and save them all on a micro-SD flash card (up to 32 GB).

Sweex 4 Port USB 2.0 Hub, at Maplin
•Small compact design•4 x USB 2.0 ports•No external power supply•Short 6 cm cable length•Colour Black

3 USB Mobile Broadband 12GB PAYG Starter Pack, at Maplins
•Latest HSPA+ technology•Up to 40% performance improvement over previous models•Network speeds of up to 21.1Mbps•Includes 12GB of pre-loaded data allowance, valid for 12 months from first usage•USB self-installing dongle (for PC)•Compatible with PCs and Macs•No contract required, simply top up when your credit has run out•Top up online - access to the 3 website is at zero cost12GB (12 months) enables you to:- Send 8000 plain text emails- Surf the web for 400 hours- Download 400 two minute videos- Download 800 music tracksYou will need to top up after you have used your data or time allowance (whichever comes first).

Novopro LS25 Pro laptop stand and bag, at Maplin
Deluxe professional producer/DJ laptop standAlluminum alloy structureQuick open and fold systemWith a second tray for soundcard or I/O deviceThin, small and lightweight but built for the rigors of the road!With a carry bag for storage and transportationOpen size: 26.5 x 22.7 x 30 cmFolded/closed size: 30 x 26.5 x 2.5 cmNet Weight: 1.07 kgsProfessional Alloy laptop stand

Maplin UK check their prices daily against other retailers making sure they have consistently low prices. Maplin has more to offer than any other online retailer, with their excellent customer service, the Maplin low price guarantee of Everyday Low Prices, 24 Hr Helpline, delivery 7 days a week and expert installation, all backed by a nation-wide network of over 400 stores. Shopping online at Maplin UK, customers can be sure they are getting the best price!

Maplin Electrical website offers UK customers a vast range of Electrical products online including a constantly updated range of Web exclusives. From Washing Machines, Widescreen TV's to the Latest in Home Computing, Maplin caters for everyone!